Laserkutteren er hovedsakelig tiltenkt personbruk/småprosjekter. Hvis man har større prosjekter man ønsker å gjennomføre med laserkutteren f.eks kulisser, utstillinger osv. som krever flere timer arbeid, er det ønskelig at man tar kontakt med mechanisk komite på OV først. Mail kan sendes til mech@omegav.no. |
Read the instructions closely before use! Make sure to open the outer window! You will not get access to the machine without training. You may not cut unknown materials. If you are going to cut material that you brought yourself, verify its safety and ask us for permission first. |
If you are using this tool for the first time, please contact a member of the board. You can find a list of approved personell here.
INNHOLDSFORTEGNELSE
Material | DANGER! | Cause/Consequence |
---|---|---|
PVC (Poly Vinyl Chloride)/vinyl/pleather/artificial leather | Emits chlorine gas when cut! | Don't ever cut this material as it will ruin the optics, causes the metal of the machine to corrode as chlorine is released and ruins the motion control system. Chlorine gas is also poisonous, you will die. |
Polycarbonate/Lexan | Cuts very poorly, discolors, catches fire | Polycarbonate is often found as flat, sheet material. It is a poor choice for laser cutting. It creates long stringy clouds of soot that float up, ruin the optics and mess up the machine. |
ABS | Melts / Cyanide | ABS does not cut well in a laser cutter. It tends to melt rather than vaporize, and has a higher chance of catching on fire and leaving behind melted gooey deposits on the vector cutting grid. It also does not engrave well (again, tends to melt). Cutting ABS plastic emits hydrogen cyanide, which is unsafe at any concentration. You will die. If you smell an almond-y smell: Stop the cut and call the poison safety line (22 59 13 00). |
High-density polyethylene (HDPE) | Catches fire and melts | It melts. It gets gooey. It catches fire. Don't use it. |
PolyStyrene Foam | Catches fire | It catches fire quickly, burns rapidly, it melts, and only thin pieces cut. This is the #1 material that causes laser fires!!! |
PolyPropylene Foam | Catches fire | Like PolyStyrene, it melts, catches fire, and the melted drops continue to burn and turn into rock-hard drips and pebbles. |
Epoxy | burn / smoke | Epoxy is an aliphatic resin, strongly cross-linked carbon chains. A CO2 laser can't cut it, and the resulting burned mess creates toxic fumes ( like cyanide! ). Items coated in Epoxy, or cast Epoxy resins must not be used in the laser cutter. ( see Fiberglass ) |
Fiberglass | Emits fumes | It's a mix of two materials that cant' be cut. Glass (etch, no cut) and epoxy resin (fumes) |
Coated Carbon Fiber | Emits noxious fumes | A mix of two materials. Thin carbon fiber mat can be cut, with some fraying - but not when coated. |
Any foodstuff ( such as meat, seaweed 'nori' sheets, cookie dough, bread, tortillas... ) | Food in laser/poison in food | Unhygienic and potentially contaminates the food with other materials/poisons. |
Giftinformasjonen (ring ved mistanke om inhalering av skadelige stoffer): 22 59 13 00
Se Identification of Polymers!
Hentet fra http://www.atxhackerspace.org/wiki/Laser_Cutter_Materials#NEVER_CUT_THESE_MATERIALS
Merk at du betaler for alt materiale som du laserkutter/graverer, ikke bare det som ender opp som ditt ferdige produkt. Vennligst kast alt brukt materiale (med hull, streker eller tegninger) i søpla ute i gangen. (TODO: Sette opp blandet avfall-dunk på Smia) |
Finn bilete av kva du skal kutte/gravere. Filformatet bør vere PNG, JPEG eller DXF (Sistnevnte gir bare streker uten tykkelse). DXF funkar bra for vektorfiler. Fleire filformat kan finnast under "Import" i RDworks. PDworks kan direkte legge inn tekst-fonter til kutting. Opne RDworks og trykk Files→Import. Importer bilete du vil gravere. Endre størrelsen oppe i venstre hjørne, til ein størrelse som passer mediet du skal kutte/gravere. Låssymbolet til høgre for måla velger Xaksen skalerast saman med Y-aksen(og motsatt), eller om bilete strekkast. Til høgre er ei liste over ulike lag. Kvart element her står det (som oftast) Scan eller Cut. Ulike lag har ulike farger. Nye lag kan lagast ved å trykke på fargeknappane nede til venstre. Dobbeltklikk på lagene du skal gravere (Scan) eller kutte (Cut). Eit nytt vindu vil opne seg, og du ser ca i midten ei liste med power. Til vanleg vil sørge for at det kun er eit element med power i denne lista. Så velger du Power likt i begge boksane, samt Speed basert på kva du vil kutte eller gravere. Sjå lista over Laserparameter for foreslåtte parameter.
IKKJE skru på Laserkutter Bodor BCL-1309XU før du har lest følgande avsnitta.
Når du er ferdig, hugs å skru av Bodor, koble ut stikkontakten, skru av vannpumpa og lukk vinduet.
http://laser101.fslaser.com/laser-safety-course