|
Glass | 2 mm | 300 | 30 | Gravering, dither 50 dpi, speilvent gravert på baksiden, invertert farge |
| IMG_20181225_142955754.jpg |
Glass | vinflaske | 300 | 30 | Gravering, no dither |
| |
Bambus | 20mm | 300 | 15 | Gravering, no dither |
| IMG_2829.JPG |
Plastglass biltema Presset Styren-akrylnitril | 4mm | 10 | 40 | Kutt. Litt røffe kanter på baksida, smelta litt for mykje. |
| |
Pizzaeske | 0.9mm | 35 | 15 | Kutt |
|
|
Pizzaeske | 0.9mm | 300 | 10 | "Gravering" |
|
|
Kork | ? | ? | ? | (UTESTET) Kan visstnok kuttes bra |
|
|
Plexiglas®/Akryl/Lucite/PMMA | ? | ? | ? | (UTESTET) Kan visstnok kuttes veldig bra |
|
|
Delrin (POM) | ? | ? | ? | (UTESTET) Delrin comes in a number of shore strengths (hardness) and the harder Delrin tends to work better. Great for gears! |
|
|
Kapton tape (Polymide) | 3mm? | ? | ? | (UTESTET) Works well, in thin sheets and strips like tape. |
|
|
Mylar | 3mm? | ? | ? | (UTESTET) Works well if it's thin. Thick mylar has a tendency to warp, bubble, and curl | Gold coated mylar will not work. |
|
Solid Styrene | 3mm? | ? | ? | (UTESTET) Smokes a lot when cut, but can be cut. |
|
|
Depron foam | 10mm? | ? | ? | (UTESTET) Used a lot for hobby, RC aircraft, architectural models, and toys. 1/4" cuts nicely, with a smooth edge. | Must be constantly monitored. |
|
Gator foam | ? | ? | ? | (UTESTET) Foam core gets burned and eaten away compared to the top and bottom hard paper shell. | Not a fantastic thing to cut, but it can be cut if watched. |
|
Cloth/felt/hemp/cotton | ? | ? | ? | (UTESTET) Kan visstnok kuttes bra. Kan lage blonder? | Not plastic coated or impregnated cloth! |
|
Leather/Suede | 6mm? | ? | ? | (UTESTET) Leather is very hard to cut, but can be if it's thinner than a belt (call it 1/8"). | Real leather only! Not 'pleather' or other imitations! |
|
Magnetic sheet | ? | ? | ? | (UTESTET) Kan visstnok kuttes veldig bra |
|
|
Gummi UTEN KLORIN | ? | ? | ? | (UTESTET) Skal gå fint å kutte | Vær sikker på at det ikke inneholder klorin! |
|
Teflon (PTFE) | ? | ? | ? | (UTESTET) Cuts OK in thin sheets |
|
|
Carbon fiber mats/weave that has not had epoxy applied | ? | ? | ? | (UTESTET) Can be cut, very slowly. | You must not cut carbon fiber that has been coated!! |
|
Coroplast ('corrugated plastic') | 10mm? | ? | ? | (UTESTET) Difficult because of the vertical strips. Three passes at 80% power, 7% speed, and it will be slightly connected still at the bottom from the vertical strips. |
|
|
Keramiske fliser | N/A | ? | ? | (UTESTET) Gravering |
|
|
Anodisert aluminium | N/A | ? | ? | (UTESTET) Gravering. Vaporizes the anodization away. |
|
|
Malt metall | N/A | ? | ? | (UTESTET) Gravering. Vaporizes the paint away. |
|
|
Stone, Marble, Granite, Soapstone, Onyx. | N/A | ? | ? | (UTESTET) Gravering. Gets a white "textured" look when etched. High power pls. |
|
|